How about this pothos hanging basin made of flowers? The key is really simple.
Material:
A red wine bottle, a piece of rope, alcohol (gasoline and lubricating oil are OK), a chopstick, 502 glue, a coat hanger, wire, white cloth in the shoe box, water moss (rags or dry leaves are OK)
Step:
1. Soak the wine bottle in water for two hours, and remove the paper package from the bottle. Then tie the rope to the place to be cut.
2. Use chopsticks to dribble alcohol on the rope and light the fire.
3. After the rope is burnt, immediately immerse the part to be cut into the cold water.
4. If the fire is full, the part to be cut will fall off by itself once it enters cold water. If the fire is not full, there will be cracks in the place where the rope is tied. Wrap it with soft cloth, knock it at the corner of the table, and the bottom will fall off.
5. Take 502 glue and apply a layer on the incision to avoid cutting. (or sanding the cut)
6. Make the hanger into a few small hooks in the shape of the figure below. The actual length of the red line in the figure below is the radius of the bottle.
7. Draw the bottom of the bottle on white paper, and put the small hook in.
8. Fix the small hook together with wire.
9. Knead the rest of the hanger into a ball, which is bigger than the bottle mouth.
10. The kneaded dough is assembled with a small hook, as shown in the following figure.
11. Assemble into the bottle.
Bottom view
12. Cut the white cloth in the shoe box into strips and put it into the bottle, then compact it with chopsticks.
13. Keep the bottle mouth down and put the water moss. You can use rags or dead leaves instead.
14. For earth filling, the water moss can be placed on the edge of the bottle, so that the earth can not be seen from the outside of the bottle, increasing the beauty.
15. After the soil is installed, plant the pothos, bamboo and plum according to your preference
16. After planting the pothos, leave a space of about 4cm to spread a layer of water moss.
17. Cut a piece of white cloth and plug it into the bottom of the bottle, as shown in the figure below.
18. Hang the bottle and pull out the white cloth at the mouth.
Dangdang ~ hanging in the balcony and living room, is it more beautiful than the monotonous green flowerpot? Although there are many operation steps, Huahua thinks they are very simple.
This flowerpot is made of plastic bottles.
Material:
A number of branches, a plastic bottle, string, scissors
Step:
1. Cut the branch into small sticks with a length of about the same length as the height of the flowerpot you need.
2. Cut off the bottom of the plastic bottle. The height must be shorter than that of the stick, and then make holes at the bottom.
3. Tie one end of the stick with wire.
4. Take another stick and wrap it two times with wire. Let it be next to the first stick. According to this method, tie all sticks together.
5. Then tie one end of the stick in the same way as above, but the winding direction should be opposite to that of the other end, or it will fall apart.
6. Stick the tied branches to the bottom of the plastic bottle with solid glue, and then bind them with wire.
7. Is it better to plant flowers on the earth than the bare plastic bottles?
Material:
Some plastic bottles, ropes, scissors, knives
Step:
1. Use scissors and knife to cut a rectangular hole in the bottle.
2. Cut four holes on the edge of the cut that can pass through the rope.
3. Put on the plastic bottles with ropes, as shown in the following figure.
4. Fill the plastic bottle and plant flowers.
Success, hanging on the living room wall, is not immediately the same, and a combination of multiple plastic bottles than a single plastic bottle to look much better!
These very fresh flower pots are made of milk powder cans!
Material:
Milk powder can, colored paper (wallpaper can also be), color pen, double-sided tape
Step:
1. Use a screwdriver and hammer to drill holes in the bottom of the pot.
2. Cut the same size of colored paper according to the size of the can.
3. Paste the color paper on the can with double-sided tape.
4. Write words or draw patterns on the can body with a colored pen.
5. Then fill the soil and plant the tender and fleshy soil.
Is this Swan very delicate? It's a flowerpot made of washing liquid bottle.
Material:
Detergent bottles, scissors, buttons, pens
Step:
1. Mark the bottle with a pen and cut it with scissors according to the mark.
2. Then draw out the shape of Swan's head at the handle of the bottle, use scissors to cut it according to the shape, and use scissors to cut swan's tail according to the figure below.
3. Paste the button on the white mark with glue to make Swan eyes. Then the Swan pot is ready!
4. Finally, fill the soil with flowers.
Old bottles and cans
The flowerpot is like a work of art.
Do you have a heart attack?
Follow the flowers and move!