I. pruning and maintenance after Rose
4. If there are many buds on the branch, and each bud is fully open at the same time, you can cut all the flowers. For strong branches, leave 3-4 leaves; for medium branches, leave 2-3 leaves. A leaf is a bud point, and then new branches will be developed.
5. If it is a small seedling and the flowering branch is weak, we only keep 1-2 leaves at the lower part of the branch, and cut off the rest.
6. When cutting branches, we should cut them into outward buds, let them go outward, don't cut them into inward buds, and finally grow into Cross branches.
7. When cutting, cut down at 0.5-0.8 cm above the leaf bud, with weak cutting and strong cutting. Pay attention to the direction of scissor bud, because the growth direction of scissor bud is the growth direction of future branches. The upper end of scissor is flush with the upper end of bud, and the lower end of scissor is flush with the waist of bud.
8. Do not dip the cut branches into water within 1 week, keep them dry, prevent them from rotting, or apply carbendazim solution to the wound.
1. The rose will consume a lot of nutrients when it blooms once. Fertilization is necessary. Nitrogen fertilizer is mainly applied after flowering. You can use organic fertilizer retting by yourself or compound fertilizer.
2. The organic fertilizer you retouch can be made by drinking the residue of soybean milk and putting it in a big bucket to retouch with water. Throw some tea leaves in the bucket to drink. It doesn't stink at all.
3. Wait until the water in the bucket is black or gray. When it is used, 20% fertilizer and 80% water will be used. Root and apply once a week. Water the next day after fertilization to prevent fertilizer damage.
4. If the organic fertilizer is too troublesome to be retreaded, it can be applied to Hefei. After the flower, a small spoon of compound fertilizer can be used to dig a shallow pit close to the basin, about 3-5cm. Put the compound fertilizer in, and then bury the soil. If your rose is planted on the ground, you can dig a hole and bury the compound fertilizer 15 cm away from the trunk.
5. Wait until the sprouts of rose grow to 2 inches (about 13 cm), and start to apply more P and K fertilizer. Add a little potassium dihydrogen phosphate to the bean cake water.
1. After the Gardenia Flower is withered, cut 2-3 pairs of leaves under the flower.
2. If you want to develop a bud as a trunk or an extended branch of the trunk, you should leave the buds that grow vertically upward and cut off the side buds. If you want to make the buds as a side branch and have a full plant shape, you can leave the buds that face outward and cut off the buds that face inward.
3. After cutting the bud once, the remaining buds will grow into branches. When pruning this branch next year, the direction of remaining buds should be opposite to that of the previous year, that is, opposite to that of the previous year.
4. Gardenia also need to prune the long branches (topping), because the side branches are many, the plant shape is plump, when pruning, leave 2-3 layers of leaves on the branches, the rest can be cut, flat cut, then leave strong buds, weak buds break.
Before pruning
After pruning
5. After pruning, spray chlorothalonil solution on the wound to prevent infection. In a few days, new buds will grow!
1. Gardenia likes acid soil and consumes a lot of nutrients during flowering. After flowering, fertilizer should be applied in time. You can use self-made bean cake and mash dregs to ripen with water, add ferrous sulfate to make alum fertilizer water, dilute with water according to the ratio of 1:50, and then fertilize gardenia. Once a month.
2. Stop watering the day before fertilization, and water once when fertilization.
1. Cut 5-8 mm above the second pair of leaves, and cut the branches and the first pair of leaves together. After a period of time can grow new buds, but also flowering again
2. The God of longevity pruning, generally only leaves about 5-8 cm of the trunk, because the longer the longevity of flowers, the less flowers, so many people after the flowering, either re cutting, or re cutting with branches, cutting methods have been mentioned recently
3. Pay attention to leave several leaves for photosynthesis and nutrient supply during heavy cutting. Cut flat, put it in a cool place to dry for 2-3 days, and do not touch the cut with water.
4. On the long-lived flower branches after heavy cutting, there will be many buds sprouting. When these buds grow to 3 pairs of leaves, we can cut them thinly, leave strong buds, cut off weak buds, and make the plant more plump.
5. When the buds grow to 5 pairs of leaves, we can take off the center and let the branches grow more lateral buds. The operation method has been mentioned before, i.e. cutting off 3 pairs of leaves at the top and leaving 2 pairs of leaves at the bottom (i.e. 4 leaves).
After June and September, the longevity flower can't be cut again, because the longevity at that time is pregnant with flower buds, and you can't appreciate it if you cut it again
1. After the longevity flower blooms, it is necessary to apply a liquid fertilizer mainly composed of nitrogen fertilizer to promote the germination of branches and leaves. The nitrogen fertilizer can be used for bean cake water, or urea can be mixed into the water to irrigate the roots.
2. In summer, if the temperature is over 30 ℃, don't fertilize the longevity flower.
3. After the long life flower, we should also ensure sufficient light, but in the noon of summer, we should put it in the place of astigmatism, and keep the ventilation, so as to burn the leaves and black rotten roots.
