If you want to have a high survival rate, the best way for flowers is hydroponics.
1. Prepare necessary materials. A basin of pothos, a pair of scissors and a hydroponic flask
2. Cut a cutting branch from the mother plant of the pothos. The best branch with air rooting, so the survival rate will greatly increase
3. Short cut the cut branches of the pothos, about 7-10CM for each branch. It is better to cut the incision into 45 ° to increase the water absorption area.
4. Put the pruned branches in the hydroponic flask, and then add water to the lower 1 /3-1 /2 of the branches. In order to ensure the rapid rooting of the pothos, you can also crush an aspirin, mix it with water according to the ratio of 1:1000 into a solution, and drop it into a hydroponic bottle.
5. Before the roots grow, change the water once every 2-3 days. At the same time, clean the inner wall of the hydroponic flask without adding nutrient solution. Wait until the roots grow out, about 5-7 days to change water, high temperature in summer, the best do not add nutrient solution, otherwise it is easy to cause root rot.
In addition to hydroponics, the most commonly used method is soil culture.
1. Preparation materials: a pot of pothos, a pair of scissors, a flowerpot, nutritious soil
2. Use scissors to cut a half lignified branch from the pothos. The length is about 10cm, and the lower end is obliquely cut into 45 °.
3. The lower leaves of the cut branches should be removed to facilitate cutting.
4. If you want to improve the survival rate of cutting, you can also insert the lower end of the branch into the rooting water for 1-2 minutes before cutting, and then dry it before cutting into the soil. The cutting depth is about 1 /2 of the branch, and then water once, put it in a cool and ventilated place for curing.
5. After cutting, the pothos must pay attention to ensure a high air humidity, usually spray water around the leaves and flowerpots, it can take about 15-20 days to take root, and then put it in a place with sufficient scattered light for maintenance.
A flower friend told Hua Hua that there are not so many branches in her family that can be used for cutting. What should I do? Let's take a look at the next way!
1. Preparation materials: 1 semi lignified branch, 1 flowerpot, cutting nutrient soil, 1 pair of scissors
2. Use scissors to cut off all the leaves on the branches of the pothos, and then cut them short. The length of each cut is about 2-4cm. At the same time, make sure that each cut has a node.
3. Insert the short cut branches into the prepared soil, and the part inserted into the soil is 1 /2-2 /3. The nutritive soil of cuttage can be perlite, vermiculite, coconut bran, etc.
4. Insert all the pothos cuttings into the soil, and then put them in a cool and ventilated place for maintenance. Do not direct sunlight.
5. The potting soil for cutting pothos must be kept in a slightly wet state, and there must be no ponding, otherwise it will lead to the rot of pothos cuttings. After a period of time, there are sprouts on the pothos cuttings, which will explode soon!
After the branches are cut short, we can also spread the pothos cuttings directly in the flowerpot, and the survival rate is very simple!
1. Cut the pothos cuttings short, spread them on the basin soil, and then pour them into the water for one time.
2. If the temperature in the home is higher than 30 ℃, do not cover the plastic bag. If the temperature is lower than 30 ℃, or the room is air-conditioned, cover the whole green broccoli pot with the plastic bag, and then put it in a place with sufficient scattered light for maintenance.
3. Make sure to open the film for ventilation every day. If the basin soil is found to be dry, water it in time. It won't be long before we can find the new buds of the green plants in the flowerpot.
4. After finding that the pothos grows new buds, lay a layer of coconut bran on the surface of the pot soil, add some urea, compound fertilizer and dilute with water, so that the pothos grows more and more prosperous!
Flower to introduce the last cutting method of pothos, is to use sponge to cut, this method is very easy to operate, you can try at home!
1. Preparation materials: 1 pot of pothos, 1 pair of scissors and 1 sponge
2. Select a robust branch from the mother plant, which contains at least one node.
3. Use scissors to poke a few small holes in the sponge, then insert the branches of the pothos into the small holes of the sponge, the depth is about 2-4cm, then put the sponge in the water, so that the sponge can fully absorb the water.
4. Make sure that the sponge block is kept in a slightly wet state. If the sponge block is dry, water it immediately, and then put it in a cool and ventilated place for maintenance. In about 1 month, you can see the rooting of the cuttage pothos!
