Many flower friends think it's hard to cut rose. Their hearts are broken. They can't help but worry about the black stem, rootless, rotten root. Huahua specially learned a cutting method of rose from the old gardener downstairs. It's very simple. The survival rate is 100%. Only one plastic bottle is needed!
Cut off a strong rose branch, 45 degrees, about 8 cm in length.
Insert the branches into the soil at a depth of 2-3cm, pour them with water, and they can be inserted into the flowerpot. If you want to plant, you can directly insert them where you want to plant, so that you don't need to transplant them.
Cut off the thin part which is close to the bottle mouth, which accounts for about 1 /4 of the bottle body, and then buckle it onto the branch. There is no need to poke holes in the bottle body. Just take the plastic bottle away when watering, and keep it in place at other times.
Generally, after 15 days, the rose will grow new leaves. But during the period, we must keep the soil moist. When the soil is dry, we must water it in time. Take off the plastic bottle and then water it.
It's better to find a large bottle, or you will touch the leaves every time.
After the new leaves of rose grow out, continue to buckle the plastic bottle for 10 days. After 10 days, you can completely remove the plastic bottle! This cuttage out of the rose branch survival rate of 100%, green leaves, no longer afraid of black!
A few plastic bottles can make a green pillar, which is super simple! The longer the green rose, the more prosperous the leaves are. The green leaves are shining, and they scratch and climb for 10 meters.
Find a clean plastic bottle, try to find a relatively strong bottle, remove the cap, first cut off the bottom of the bottle, and then use the red iron chopsticks to iron out 20 holes of uniform size.
Put a pine needle on the bottom of the basin and stand the plastic bottle in the center of the basin.
Fill the soil in the basin, fill the plastic bottle with pine bark or pine needles, let the bottle stand stably in the basin, then plant the pothos around, and water it.
Find the second plastic bottle, which is a little larger than the diameter of the first one, or poke a hole in the bottle body, cut off the bottle mouth and bottom, and insert it into the first one.
Fill the second bottle with pine bark, let it stand, and add a little cake fertilizer.
Wrap the mineral water bottle with palm skin, generally 2 layers are enough, and then tie it with rope for several circles to fix it.
Now the vines of the pothos are still short. Two plastic bottles are enough. When the pothos grows up, you can continue to insert the bottles to make the pothos column higher.
When you mention a plastic bottle to make a flowerpot, some flower friends will say it's ugly. That's because you didn't choose the right bottle. If you choose some more textured drink bottles, you can make a beautiful flowerpot by cutting two knives
Just like the two bottles below, the color is pretty good, and the bottles are also relatively strong.
This drink bottle is suitable for making flowerpots horizontally. First, cut a rectangular mouth on the bottle body, and then poke a few holes on the side of the bottom of the pot to make water.
In order to make the flowerpot more beautiful, you can cut the edge into beautiful serrations, which is more layered than when you don't cut it.
Just plant the flowers, the color of the bottle and what kind of flowers are very beautiful!
Sometimes when I go far, I don't have time to water the flowers. I'm always worried that the flowers will die of drought. In fact, I can use a plastic bottle to finish it all! Let's see how the automatic water absorption flowerpot is made!
Cut the plastic bottle into two parts, poke holes in the bottle cap, let the cotton thread pass through, and plant more meat on the part with the bottle cap. The other part of the bottle is filled with water, and the other end of the cotton thread is put inside to absorb water.
Insert the fleshy part of the bottle into another part, so that the water at the bottom of the bottle will slowly seep into the soil through the cotton thread, and keep the soil moist. The meat must grow well!
In addition to the automatic water absorbing flowerpot, the plastic bottle can also be used as an automatic watering artifact. Even if you are far away from the door, you are not afraid of the death of the flowers at home. It is very reassuring!
Fill the plastic bottle with water. Fill it with 8 minutes. Screw up the cap. Don't let the water leak. Then make small holes in the cap and bottom. Use a needle. The holes are not too big. Just let the water flow out.
Put the bottle mouth down into the flowerpot, and then insert the stick into the pot soil to support the plastic bottle. So the water will slowly flow into the soil!
Some meat is hairy. When watering, you can't let the leaves stick to the water. Otherwise, it's easy to rot. if there is a sharp and fine watering artifact, only you have a plastic bottle. Flowers can make it!
Find a piece of paper and fold it into a cone.
Stick the tape on the cone paper, especially on the sharp end, and make it harder.
Use a lighter to soften the cap. Don't light it. Then insert the cap with a cone-shaped paper and stretch the cap. After adjusting to the desired length and tilt angle, let it cool down completely.
After cooling down, take out the paper, and then cut off the tip of the bottle cap. It can permeate water.
Put water in the bottle, screw the cap, and then pour more meat. You won't be afraid of water getting on the leaves!
Cutting is always unsuccessful flower friends, you can try high-pressure method, especially those flowers that are not easy to root, such as figs, grapes, woody Hydrangea, etc., using high-pressure method will greatly improve the rooting life rate!
Prepare mineral water bottle, knife, scissors, tape, peat soil or water moss, etc.
Choose robust branches with a diameter of more than 0.5cm. Use a black pen to draw the position of peeling a circle. The distance between the two lines is about 1cm.
Use a knife to peel off the bark until the white part of the branches are exposed. Start gently and slowly.
Cut the plastic bottle. The bottom part of the bottle is about 12cm high. Then cut a knife from the side. Cut a round hole at the bottom to let the branches pass through.
Put the bottle on the peeled branches, and then stick the side cut with adhesive tape.
You can roll a paper tube to pour peat soil into the bottle, and then add some water moss, which is more conducive to root. The soil covers the place 2 cm high above the girth opening.
Tie the plastic bottle with wire, and let the plastic bottle and soil be fixed together.
Water the plastic bottle thoroughly.
Find a plastic bag and tie it to the top of the bottle. It can keep warm and reduce water loss. Keep the soil moist during rooting.
About a month later, through the plastic bottle, you can see that there are many roots in the bottle. Then you can remove the plastic bottle and cut the branches.
After cutting the branches, you can go to the basin. After going to the basin, you can cut off some leaves to make the flower clothes basin faster
